
Dual Channel 31-band Graphic Equalizer/Limiter with Type III Noise Reduction
Series: 20
Model: 2231
Part #: DBX2231V
- Revolutionary instant encode/decode Type III noise reduction in-circuit at the push of a button
- Increases S/N ratio by up to 20dB
- Patent-pending PeakPlus limiter threshold range from 0dBu to +24dBu (off) can transparently tame the wildest hits or the subtlest nuances of any signal
- Four segment LED bargraph for both gain reduction and output level offers the most comprehensive visual feedback available
- Status LEDs offer visual feedback for all settings on the front panel
The 2231 graphic equalizer shall be a mono 31-band type with frequency centers on standard ISO 1/3 octave frequencies ranging from 20Hz to 20kHz. The boost/cut range shall be switchable via a recessed front panel switch to either +/-6dB or +/-15dB and the selected range shall be indicated on the front panel by either of two LEDs. Low-noise equalization sliders having a 45mm travel shall be utilized having center detents at 0dB. The equalizer shall have a front panel 41-detent rotary input gain control having a +/-15dB range. Bypassing the equalizer section of the signal path shall be accomplished via a front-panel switch having a corresponding LED to indicate when it is bypassed. A 40Hz low-cut Bessel filter with 18dB/octave slope shall be insertable in the signal path via a front panel recessed switch and shall have an LED to indicate when the filter is active. The graphic equalizer shall incorporate dbx Type III™ Noise Reduction providing up to 20dB of broadband noise reduction, having a front panel switch to enable the noise reduction and an LED to indicate when it is active. The equalizer shall also be equipped with a dbx PeakPlus limiter system. Electronically balanced/unbalanced inputs shall include 1/4" TRS, female XLR, and screw terminal barrier strip, while servo-balanced/unbalanced outputs shall include 1/4" TRS, male XLR, and screw terminal barrier strip shared with the input.
- Revolutionary instant encode/decode Type III noise reduction in-circuit at the push of a button
- Increases S/N ratio by up to 20dB
- Patent-pending PeakPlus limiter threshold range from 0dBu to +24dBu (off) can transparently tame the wildest hits or the subtlest nuances of any signal
- Four segment LED bargraph for both gain reduction and output level offers the most comprehensive visual feedback available
- Status LEDs offer visual feedback for all settings on the front panel
- Equalizer Input Connector - 1/4" TRS
- Equalizer Input Connector - XLR
- Equalizer Output Connector - 1/4" TRS
- Equalizer Output Connector - XLR
- Equalizer Type - Graphic Equalizer
- Warranty - Yes
- Rackmountable - Yes
- Spec Sheet available - Yes
- Impedance: Balanced 40 kOhm, unbalanced 20 kOhm
- Impedance: Balanced 200 ohm, unbalanced 100 ohm
- Bandwidth (octaves): 0.33
- Depth: 7.90 in
- Height: 5.25 in
- Width: 19 in
- Input Connectors: 1/4" TRS, female XLR (pin 2 hot) and barrier terminal strip
- Input Type: Electronically balanced/unbalanced, RF filtered
- Input Impedance: 40 kiloohms (balanced), 20 kiloohms (unbalanced)
- Max Input Level: >+21dBu balanced or unbalanced
- Input CMRR: >40dB, typically >55dB at 1kHz
- Output Connectors: 1/4" TRS, male XLR (pin 2 hot) and barrier terminal strip
- Output Type: Impedance-balanaced/unbalanced, RF filtered
- Output Impedance: 200 Ohms (balanced), 100 Ohms (unbalanced)
- Max Output Level: >+21dBu balanced/unbalanced into 2 kiloohms or greater, >+18dBm balanced/unbalanced (into 600 ohms)
- Bandwidth: 20Hz to 20kHz, +0.5/-1dB
- Main Connection: IEC receptacle
- Certifications: CE
- Dynamic Range: 120 dB
- Rack Units (Height): 3
- Rackmountable: Yes
- Total Harmonic Distortion + Noise (THD+N): 0.04 %
- Warranty (Length/Type): 2 Years
- AC Voltage: 230 Volts
- Active Power: 28 Watt
- Noise: 20 dB
Suggested Products

Kore Multimedia Solutions
5100 Verde Valley Lane
113
Dallas, TX 75254
USA
(469) 998-1261
https://www.koremmsolutions.com/